Displayinnstillinger

Eye3 Display:

Dette displayet finner du på Dualtron ,Speedway og en del Kaboo sparker.

P0 - Wheel Size (not rim size)
P1 - Nominal Battery Voltage
P2 - Magnet count
P3 - (?) should be at 0
P4 - Speed Unit
P5 - Start Method (Kickstart or Stand still - start)
P6 - Cruise Control
P7 - Soft Start setting
P8 - Max Power Output
P9 - Battery Save mode

PA - Electronic Brake (regenative)
PB - LCD Brightness
PC - Off timer
PD - ABS toggle

QS-S4 displayet:

Videoen tar utgangspunkt i Zero 10X . Instillingene gjelder på alle modeller med samme display og først finner du listen over hva de forskjellige settingsene gjør, hva som er riktig for din modell, kommer an på hvilken modell du har iht batteristørrelse, motor og preferanser.

 

MODE - This will effect the top speed of your scooter. The gears range from 1 to 3, 3 being the fastest mode. You can toggle through modes by simply clicking the "mode" button. When you power off the scooter, it defaults back to mode 1.

TRIP AND VOLTAGE - You can toggle your main display from odometer, to trip, to voltage display by simply clicking the power button.

P SETTINGS - In order to access the "P" settings, you'll want to simultaneously hold the power and mode button down for about 3 seconds. If done correctly, you'll be presented with a screen reading "P 01" To toggle through the setting options you'll use the power button, and to change the settings you'll use the mode button.

P 01, LCD BRIGHTNESS - This setting adjusts your LCD brightness. The options are 1 through 3 with 3 being the brightest. The brightness of the LCD has insignificant effect on battery life. We recommend 3 because it's easier to see in bright conditions.

P 02, MILAGE - You can choose between miles and kilometers.

P 03, VOLTAGE - This displays the voltage. Dependent on the scooter.

P 04, AUTO SHUT OFF - This allows you to choose (in minutes) when you're scooter will automatically shut off due to inactivity. 

P 05, UNUSED

P 06, WHEEL DIAMETER - This simply displays the wheel diameter. 

P 07, MAGNETS - This simply displays the number of magnets on the motor. We recommend not changing this setting.

P 08, POWER LIMIT - This allows the user to choose the power limit of their scooter. The options are 1-100 with 100 being maximum power. WARNING! DO NOT hit mode on this setting if you do not plan on changing the power level. It will put you down to 001, and in order to get back to 100, you'll need to press the button 99 times. No one wants to do that.

P 09, KICKSTART - Here you can choose between kickstart or zero start. 00 is zero start, meaning to momentum is needing to trigger the motor with the throttle. 01 is kick start, meaning it needs a push of momentum to trigger the motor with the throttle. We recommend kickstart. It can be dangerous if you have zero start enabled and you accidentally hit the throttle or if the throttle gets caught on something. 

P 10, UNUSED

P 11, ELECTRONIC BREAKING - This allows users to choose the intensity of the electronic breaking. The options are 1 through 5 with 5 being the strongest. We recommend 3 for the smoothest deceleration.

P 12, ACCELERATION - This allows users to choose the intensity of acceleration. The options are 1 through 5 with 5 being the quickest acceleration. We recommend 3.

P 13, UNUSED

P 14, UNUSED

P 15, CUTOFF VOLTAGE - We recommend not changing this setting because it has a large effect on battery health.

P 16, ODOMETER RESET - This allows users to reset their odometer. This only works with low milage scooters. You will not be able to zero the odometer if you're over a few miles.

P 17, CRUISE CONTROL - This allows users to toggle cruise control on or off. 00 is cruise control off. 01 is cruise control on. With cruise control on, it will be triggered if the user maintains a speed and throttle for approximately 10 seconds, it will keep the speed until the user hits the break or throttle again. We recommend keeping this off if you're not an advanced rider. 

P 18, 19, 20, UNUSED

Z-displayet:

 Emove cruiser, iconic cruiser, momas s2 . Dette displayet brukes på de fleste sparkene på det norske markedet pr idag.  Vær obs på at det er en feil i videoen:

 For the EMOVE Cruiser P0 = 10 (10" wheel) For the EMOVE Touring P0 = 8 (8" wheel) If the settings for P0 is not following this, you might find yourself at a different displayed speed compared to the actual real life speed. For example, if you Cruiser P0 setting is set at 8, you might be travelling at 25mph but the display is showing 20mph. At the time when the video is made, this is 1 minor mistake on the tutorial. Apologies for any inconveniences caused.

Her er oversikten over hva de forskjellige innstillingene betyr:

P0 - wheel diameter. Set this number to whatever you're wheel diameter is
P1 - is the low voltage protection. Set this to the correct number to ensure a safe and usable battery. If you have the 52V CRUISER, put this setting to 43.0 if you have the 48V TOURING put this setting to 41.5
P2 - is the minimum wattage, also reffered to as number of motor pole pairs. Normally our scooters leave here at 15. So i suggest just setting that to 15, like we do.
P3 -this is the speedometer setting it SHOULD just be locked at 1 with no way to change it.
P4 - is the setting that will swap your display from kilometers and miles. 0 is km/h and 1 is MPH
P5 - Throttle or kick start option. 0 allows throttle to start. 1 will deactivate it and force you to kick start.
P6 - this is the cruise setting. 1 is on and will let you use cruise control. 0 turns cruise control off
P7 - pick up speed, this is going to effect how harsh the acceleration on the scooter is. If you want a softer acceleration, put the setting to 1. If you want a hard acceleration put the setting to 0
P8 - this is the maximum speed setting, lowering this will limit how fast the scooter will go, generally this will be kept at 100 but you can lower it if you want for safety.
P9 - electric brake settings. 2 is strong, 1 is weak 0 is off.